PVC Membrane Roofing in Keller & DFW

PVC Membrane Roofing in Keller and Across DFW
3:16 Roofing and Construction installs PVC membrane roofing on flat and low-slope roofs for homes and commercial buildings in Keller and cities across the DFW Metroplex. We are family-owned, founded in 2017 by Marcos and Rachel Garza, with our office at 424 Keller Pkwy. We hold RCAT Reg. #03-0246 and are an IBHS FORTIFIED Roofer, BBB A+ Accredited and an NTRCA member. Every project starts with a free roof inspection.
What PVC membrane roofing is
PVC (polyvinyl chloride) roofing is a single-ply membrane: a flexible sheet, delivered in rolls, laid over the roof in one layer above the insulation. The seams are welded together with hot air, so the finished roof works as one continuous sheet rather than pieces held by tape or glue. PVC is commonly white or light in color, which reflects more sunlight than a dark roof.
PVC is often considered over restaurant kitchens, where exhaust vents put grease on the roof. Whether a given membrane suits the grease, oils or chemicals that reach a roof depends on the product, so the manufacturer's compatibility guidance decides the choice.
Where PVC fits on homes and commercial buildings
On a home, PVC goes where the roof is too flat for shingles: a porch or patio roof, a room addition, a garage, or a flat section that ties into a pitched roof. Shingles rely on slope to shed water: roof sections below the lowest slope the shingle maker allows need a covering made for low slopes, such as a membrane.
On commercial buildings, PVC fits offices, retail centers, restaurants, churches and warehouses with flat roofs.
PVC or TPO: choosing the right membrane
We install both. They look alike from above and both have heat-welded seams, but they are different materials: PVC is often considered where grease reaches the roof, and TPO is common on roofs without that exposure; the manufacturer's guidance for the specific product settles it. We recommend one after we have seen your roof, how it drains and what sits on it. Read more on our TPO and flat roofing page.
How we install a PVC roof
First we decide whether the existing roof can stay under the new one or has to come off (see the questions below). Then we install the insulation and any board layer your roof needs, fasten or adhere the membrane, and weld every seam. The detail work matters most: edges, walls, drains, pipes and HVAC curbs each need carefully designed flashing. We check the welded seams before we call the job finished.
Keeping a PVC roof in service
A flat roof is built to drain, not to hold water, so keep drains, scuppers and gutters clear. If water still stands after the drains are clear, have the drainage and slope looked at: low spots may need changes to the roof itself, which a new membrane alone does not fix. Keep foot traffic to the paths you need for HVAC service, because dropped tools and sharp debris can puncture a membrane. Have the roof looked at after a major hail or wind storm and whenever you see a ceiling stain. An isolated seam or flashing problem may be repairable; that also depends on whether water has reached the layers under the membrane.
How our free inspection works
1. You reach us. Call (817) 402-7663 or use the form on our Contact Us page, and we set a time that suits you.
2. We look at the whole roof. We check the membrane, the seams, the flashing at walls, edges and curbs, and the drains, and we note any standing water.
3. We photograph what we find, so you can see the same things we saw.
4. We walk you through it. We tell you whether the roof needs a repair, a new roof or no work at all, and we give you a written estimate for any work we recommend.
The inspection is free.
PVC roofing questions
What is the difference between PVC and TPO roofing?
Both are single-ply membranes with heat-welded seams. PVC is often considered where grease reaches the roof; the right product depends on what reaches your roof. We install both and recommend one after we inspect your roof.
Can PVC be used on a home?
Yes, on the parts of a home that are flat or nearly flat, such as a porch roof, patio roof, addition or garage. Steeper parts of the roof stay in shingles or another sloped-roof material.
Can a new PVC roof go over my existing flat roof?
Sometimes. It works only when the existing roof is dry, the deck and structure can carry the added layer, and local code allows it. Wet insulation has to come out first, or the moisture stays trapped inside the roof, and PVC may need a separation layer over materials it should not touch, such as asphalt. We check before we recommend either way.
How does a PVC roof handle hail and high winds?
PVC can be damaged by hail. How well a roof resists hail depends on the membrane and on what supports it, and how well it resists wind depends on the tested roof assembly, how it is attached and how its edges are built. Have the roof checked after a major storm.
Do you repair existing PVC roofs?
Yes. Small punctures and open seams can often be repaired by welding new PVC over a cleaned area. We inspect first, because the leak inside is often not directly under the opening in the roof.
How long will a PVC roof last?
That depends on the membrane, the quality of the seam welds and flashing, how well the roof drains and how it is cared for. Written warranty details are in your contract.
How do I schedule a free inspection?
Call (817) 402-7663, Monday to Saturday, 8 AM to 5 PM, or use the form on our Contact Us page.
Have a flat or low-slope roof in Keller, Southlake, Colleyville, Grapevine, Trophy Club, Roanoke, North Richland Hills, Fort Worth, Flower Mound or elsewhere in DFW? Call (817) 402-7663, Monday to Saturday, 8 AM to 5 PM, for a free roof inspection.

